ProbitLab2 V4.14.zip (2024-02-23)
Changes related to ProbitLab2 V4.13:
· For ProbitBench V4.3.3.0 and higher
· Internal optimizations
Changes related to ProbitLab2 V4.12:
· For ProbitBench V4.3.0.0 and higher
· Revised communication protocol for future needs
Changes related to ProbitLab2 V4.11:
· For ProbitBench V4.2.8.0
· Revised communication protocol for future needs
· Bugfix usage of internal I2C bus
Changes related to ProbitLab2 V4.10:
· For ProbitBench V4.2.5.0, V4.2.6.0 and V4.2.7.0
· Revised communication protocol for future needs
· Note: This update allows higher accuracy of analog voltage measurement of the DALI input and the DALI input receiver thresholds. To make use of it, please calibrate with the Probit Calibrator Tool V4.3 (see below).
Changes related to ProbitLab2 V4.9:
· For ProbitBench V4.2.1.0, V4.2.2.0 and V4.2.3.0
· Optimization of firmware to run 3xx test sequences
· Optimization of transmission timings
Changes related to ProbitLab2 V4.8:
· For ProbitBench V4.2.0.0
· Revised communication protocol for future needs
· Bus receiving optimized
· Bugfix transmission timing issue
Changes related to ProbitLab2 V4.7:
· For ProbitBench V4.2.0.0
· Revised communication protocol for future needs
· Relay switching behaviour optimized
· Receive / Transmit LED blinking behaviour optimized
· Bus receiving optimized to allow faster transmissions by ProbitBench
· Bugfix 15 bit frame transmission issue
· Bugfix resync issue
Changes related to ProbitLab2 V4.6:
· For ProbitBench V4.1.0.0 and V4.1.1.0
· Revised communication protocol for 103 and future needs
Changes related to ProbitLab2 V4.5:
· For ProbitBench V4.0.0.4 and V4.0.0.5
· Revised communication protocol for future needs
Changes related to ProbitLab2 V4.4:
· For ProbitBench V4.0.0.3
· Bugfix regarding frame transmission handling
Changes related to ProbitLab2 V4.3:
· For ProbitBench V4.0.0.2
· Bugfix regarding sporadic communication errors
Changes related to ProbitLab2 V4.2:
· For ProbitBench V4.0.0.2
· Revised communication protocol for future needs
Changes related to ProbitLab2 V4.1:
· For ProbitBench V4.0.0.1
· Bugfix regarding transmission of a frame sequence
Changes related to ProbitLab2 V4.0:
· For ProbitBench V4.0.0.1
· Introduction firmware version
Probit Calibrator Tool V4.3.zip (2019-11-16)
Probit Driver Package 2.12.36.4 WHQL.zip (2021-08-30)
Changes related to Probit driver 2.12.28:
· Driver optimizations
· ProbitSite device added
Changes related to Probit driver 2.12.06:
· Driver optimizations
· ProbitLab2 device added
Changes related to Probit driver 2.08.24:
· Driver optimizations
· preliminary Windows 8 driver installation added
Changes related to Probit driver 2.08.02:
· Windows 7 compatibility added
ProbitLab2 – Getting Started.pdf (2017-05-10)
How to get started with ProbitLab2
ProbitLab2 – Example.pdf (2017-05-10)
Example of DUT connection to ProbitLab2
Why the ProbitLab2 is not running?
Answer: Please make sure the main supply is connected correctly to the ProbitLab2 and the main supply switch at the back side is on.
Answer: Please make sure the emergency button is not pressed.
Why I cannot measure a voltage at the DALI terminals?
Answer: After power up of the ProbitLab2 the DALI terminals are disabled. After connecting with the ProbitBench software you are able to activate the integrated DALI bus power supply.
© 2025 Lichtvision Engineering GmbH - All rights reserved
Imprint | Cookie Policy | Declaration of data protection | Privacy Statement